There are many real estate renovation procedures and many details. It is comprehended that wallpaper construction is the last procedure for hard decoration of the house decoration, the beginning of smooth decoration. Wallpapers ought to be completed in all hardware such as for example woodworking, paint, water and energy, plastering, and after a sanitary washing.
Flooring and skirting are installed
❖ Avoid smashing the keel, sawing hardwood, etc. when laying the floor to help make the wallpaper dirty.
❖ Avoid vibration when setting up the baseboard, which in turn causes the wallpaper to split up from the wall surface, resulting in bubbling and curling of the wallpaper.
❖ Avoid a whole lot of dirt pollution and bruises when slicing the baseboard.
❖General putty will never be approved at the bottom of the wall, the first wallpaper can’t be cut neatly, very long time is prone to curling, causing the wallpaper to roll up.
❖ Avoid kicking the skirting range by sealing the wallpaper with glass glue, so that the drinking water molecules in the wall structure can not be discharged, resulting in mildew of the baseboard.
Following the kicking line is installed, it is possible that the wall and the skirting line aren’t flat plenty of or have a gap. The post-installed wallpaper gets the effect of covering the gap.
Door cover and door are installed
First install the entranceway in order to avoid the wallpaper from being damaged and filthy, and it is also simple to repair the color. If the wallpaper is definitely patched and the color is normally repaired (the gap between your door cover and the wall structure and the gap between the skirting lines) will stain the wallpaper.
The size of the card can vary greatly. If the size is normally too small, the wallpaper will end up being Stone paper Wall covering attached first, and a blank can look after the door is set up. If it’s full, it will quickly draw the wallpaper when the door is installed, causing harm to the wallpaper.
Wood lacquer finish can not be wallpapered first, then wood lacquer
❖Because the hardwood lacquer is sprayed during construction, the paint will stick to the wallpaper. And when the paint is usually applied, the completed product should be shielded. In particular, the surrounding wall of the cabinet, door, partition, etc. should be protected with a protective film. If it is atomized to the wall structure surface, the construction quality of the wallpaper isn’t guaranteed, in fact it is easy to cause problems.
Air conditioning hole is well
❖ Avoid punching and damage the wallpaper.
❖ Avoid wall structure vibration when punching, leading to the wallpaper to fall off.
❖ Avoid dusting the wallpaper when punching.
Curtain rod hole is pre-made
The positioning of the curtain hanging rod support is smartly designed, and the hole was created to avoid the hole punching the top of wallpaper. Especially for flocking, silk, deep embossing, special materials and additional hard-to-care wallpapers, be sure to pre-pull the curtain rod holes before pasting.
How to paste wallpaper?
Take away the wall skin: take away the original color and various other objects on the wall, make use of gypsum powder to fill the cracked portion of the wall structure, and place a bandage after flattening; if it is sand gray wall structure, partition wall, it must be covered with cup cloth Or indeed good cloth; some low quality partitions or exterior walls to attain the insulation effect, need to be filled with plasterboard
Slice the wallpaper: first measure the elevation of the wall structure, then cut the length of the wallpaper, generally there are two types of cases: simply no flower wallpaper according to the elevation of the wall structure is cut about 5 to 8 cm duration, as the upper and lower trimming: the flower wallpaper needs to consider the pattern symmetry Sex, therefore the length of the cut should be increased according to the actual situation, generally 8 to 10 cm longer.
Applying glue: Apply the wallpaper glue to the trunk of the cut wallpaper with a brush, spend special attention to the surrounding edges to become coated with glue to guarantee the structure quality, the painted wallpaper, and the glue to handle the fold. 5- 10 minutes (remember that no external drive should be applied to prevent creases in the wallpaper, especially the fabric). After the glue 
is totally penetrated into the paper, it can be posted, and several wallpapers are applied each time and posted to be able. Special material wallpaper should be glued on the wall structure, such as velvet sound-absorbing wallpaper, gold foil tin wallpaper, etc.
Wallpaper structure: Generally, the initial wallpaper is posted from the top to the bottom of the door or the part of the corner. Use the squeegee throughout, from the within to the outside, softly scrape the wallpaper, squeeze out the bubbles and surplus glue to make the wallpaper smooth. Near to the wall.
Wallpaper construction: Generally, the first wallpaper is posted from the very best to underneath of the door or the part of the corner. Utilize the squeegee from top to bottom, from the within to the outside, lightly scrape the wallpaper, squeeze out the bubbles and excess glue to help make the wallpaper flat. Near to the wall.
Before wallpapering, switch off the power: When wallpapering, should you have a power switch or socket on the wall, you can turn off the main power supply, then cover the wallpaper with all the power and socket, and cut two pairs from the guts of gravity. The corner range will show four small triangles, and then use the utility knife to eliminate the excess wallpaper around.
Trimming and cleaning: Cut off the surplus wallpaper at the top and reduced ends. The edge of the knife ought to be sharp in order to avoid burrs. When slicing some wall coverings, it is best to make use of a Japanese imported blade with a cost of just one 1.5 yuan. Then make use of a sponge dampened with water to completely wipe the glue remaining on the surface of the wallpaper to prevent the wallpaper from turning yellowish. If the wallpaper is dry following the wallpaper is dry, use a knife to cut the injected glue and flatten it to get rid of it. it is good)